Linear Gate Motor & Opener Nationwide

Linear Gate Motor & Opener in Dallas: What to Know First

We repair and install Linear gate motors and openers across Dallas, and most jobs are completed in one visit. A Linear swing-arm motor replacement typically runs between $850 and $1,400 depending on the series and whether the arm bracket survived the failure. A full slide-gate operator swap usually lands between $1,200 and $1,900. You get a written price before any work starts, not after. If your Linear gate is dead, grinding, or reversing for no reason, call (469) 299-5902 and a live person answers.

Call (469) 299-5902

This page is for Dallas homeowners who own a Linear operator and want to know what actually fails on these units, what it costs to fix, and whether the repair is worth doing. We are an independent Linear service provider, not a factory authorized dealer. That matters because we repair what’s on the property instead of steering you toward a brand swap.

Key Takeaways

• Most Linear gate motor repairs in Dallas run $250 to $600; full motor replacements run $850 to $1,900.
• Linear’s most common failure in Dallas heat is the control board, not the motor itself.
• We stock Linear OEM boards and arms locally, so most repairs happen same day or next day.
• Every Linear job includes a written price upfront and a photo record when we leave.
• Your repair is covered by the 365-Day Done Right Promise. If it is not right, we make it right, no fee.

How Linear Products Fail - and How We Fix Them

Linear is a workhorse brand. The motors themselves rarely die without help. What fails first are the electronics, the limit settings, and the mechanical connections around the motor. Here is what we actually find on Dallas properties, named by series where it matters.

• Linear LDO50 and LDO33 swing-arm operators: the capacitor gives out in the heat. These residential swing operators use a start capacitor that degrades faster in sustained 100-degree attic and pillar-box temps. The symptom is a motor that hums but will not start, or starts only after several attempts. The fix is a capacitor replacement ($120 to $190), not a motor replacement. We check the microfarad rating before quoting either.
• Linear SL and SLR slide-gate operators: limit switches drift, and the gate slams the post. The rotary limit assembly on older SL units is friction-set, and after a few thousand cycles it walks. The gate over-travels, hits the end post hard, and the board logs a fault. We re-set the limits, photograph the new position, and replace the limit nut if the detent is stripped. A limit re-set runs $150 to $225; a new limit assembly runs $240 to $320.
• Linear APeX and MegaCode receivers: phantom openings and dead remotes. Dallas has dense RF noise from cell towers, airport radar, and neighboring gate systems. Older Linear MegaCode receivers lock onto a weak frequency and a neighbor’s remote starts opening your gate, or your remote stops working after a storm. We re-address the receiver, clear ghost codes, and if the board has drifted, replace it with a current APeX receiver. This is a $180 to $300 fix, and it stops the gate from opening at 3 a.m. for no visible reason.
• Linear PB series photo-eyes: misalignment from gate-post movement. Dallas clay soil expands and contracts, and gate posts shift a half inch seasonally. The photo-eye (the infrared beam that keeps the gate from closing on a car or a person) gets knocked out of alignment, and the gate refuses to close, or reverses mid-cycle. We re-align the eyes, check the mount brackets for stress cracks, and add a shim if the post has moved. Most alignment calls are $110 to $160.
• Linear arm brackets on swing gates: fatigue cracks at the weld point. The LDO series uses a bolt-on arm bracket, and after a few years of wind load, the bracket cracks at the mounting plate. The gate still works, but it clunks, and one day the arm lets go and the gate free-swings into a car or a fence. We replace the bracket with a heavier aftermarket plate when the original is undersized, and re-weld the pivot if the post side is salvageable. This prevents a $1,200 gate panel replacement for the cost of a $180 bracket job.

Before

After

Our Linear Gate Motor & Opener Process

Here is what happens when you call us about a Linear operator in Dallas, from the first ring to the last bolt.

1. 1
   You talk to a live person. No voicemail, no call center script. We ask what the gate is doing: dead, grinding, reversing, opening on its own. That tells us which parts to bring.
2. 2
   We name the price before we touch the gate. The diagnostic fee is flat and written. If the repair is obvious from the symptom and the series, we write the repair price on the spot. You approve it in writing before any work starts.
3. 3
   We diagnose in front of you if you want to watch. We test the capacitor, check the limit switch, verify the photo-eye beam, and read the board for logged faults. You hear what we find, in plain terms.
4. 4
   We make the parts decision with your budget in mind. If a Linear OEM board is available locally, we quote it. If a quality aftermarket equivalent has a better failure record, we tell you and quote both. We never install junk to hit a lower price.
5. 5
   We test the full cycle at least a dozen times. Open, close, obstruction reverse, remote, keypad, intercom. The gate has to stop on a dime during a photo-eye trip, and the motor has to cycle without a whine.
6. 6
   You get the record before we leave. A photo log of what was found, what was set, and what was installed. The part number is on the invoice. The limit-switch setting is photographed. That is Haven Standard Clause 4, and it is not optional.

What Linear Gate Motor & Opener Costs in Dallas

Here are the numbers we quote most often on Linear work in Dallas, in writing, before the job begins.

• Diagnostic visit (applied to the repair if you proceed): $75 to $125
• Limit switch re-set and photo-eye re-alignment: $110 to $225
• Capacitor replacement on LDO swing arms: $120 to $190
• Control board replacement (APeX or MegaCode): $280 to $520
• Full swing-arm motor replacement (LDO50/LDO33): $850 to $1,400
• Full slide-gate operator replacement (SL/SLR): $1,200 to $1,900
• Battery backup installation for existing Linear operator: $450 to $700

What moves the price: whether the arm bracket is intact, whether the board has water damage, and whether the photo-eyes can be re-aligned or need replacement. A post that has shifted will add work on any brand, Linear included. The price we quote is the price you pay. We do not surprise you at the end. Call (469) 299-5902 and we’ll give you a written number based on your series and symptom.

Why Dallas Homeowners Call Vance Gate Repair Dallas for Linear Work

Adrian Vance started in commercial access control before he ever touched a residential driveway gate, and that habit never left. Every Linear job we do leaves with a photo record and a written price. Name what you found. Name what it costs. Name what you left behind. That is the whole standard.

We are not a Linear dealer trying to sell you a new operator. We are an independent service company that fixes the Linear motor you already have. And if your property runs a mix of brands, that is fine. We service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing on the same property without blinking. One company, whatever motor is on the gate.

The 365-Day Done Right Promise covers every Linear repair we complete. If it fails inside a year, we return and make it right. No argument, no fee. And we answer the phone at 3 a.m. the same way we answer at 3 p.m.: with a person.

FAQs

Get Your Linear Gate Motor Fixed in Dallas

We service every Linear residential operator in Dallas with a written price before any work starts and a photo record when we leave. Call (469) 299-5902 and a live person answers, any hour, any day. Tell us what the gate is doing. We’ll name the likely fix, the price range, and when we can be there.

Written by Adrian Vance, Owner, Vance Gate Repair Dallas at Vance Gate Repair Dallas, serving Dallas and nearby areas.