Gate Installation in Dallas - Free Survey, One Written Price

Trusted Gate Installation for Dallas Homeowners

A new driveway or pedestrian gate in Dallas typically costs between $3,400 and $11,000 installed, depending on the gate material, the motor brand, the length of the run, and whether you need a new concrete pad poured for the post. Most installations are completed in one to two days once materials arrive. Vance Gate Repair has installed and repaired over 22,000 gates since 2014, and every single installation starts the same way: a written price handed to you before any tool touches your property.

Call (469) 299-5902

We’re led by Adrian Vance, who came out of commercial access-control work in 2014 and brought the documentation habits of that world into residential driveways across Dallas. That means you get a photo record of what was built, what was set, and what was wired. You get a part-number list. And you get a one-year promise that if something isn’t right, we make it right at no charge. If you’re considering a new gate installation in Dallas, call (469) 299-5902 and a live person answers, day or night.

What Our Gate Installation Service Includes

Every gate installation we do in Dallas begins with a measured site visit, a written scope of work, and a fixed price. Nothing is verbal. Nothing is estimated on a handshake. The price you approve is the price you pay. Here’s how that works across each type of gate we install.

Driveway Gate

A driveway gate is the main vehicular gate at the front of your property, and it’s the one that carries the most daily cycles, which means the post footings, hinge points, and operator sizing matter more than anything else on the job. In Dallas, we commonly see driveway gates fabricated from steel, aluminum, or ornamental iron, and the installation almost always includes running conduit for the motor, setting the posts in concrete, and dialing in the opener’s travel limits so the gate doesn’t slam at the end of its arc. We photograph every stage, including the footing depth before the concrete goes in.

Pedestrian Gate

A pedestrian gate is the walk-through gate alongside or separate from the driveway, and in Dallas neighborhoods like Lakewood or Preston Hollow, it’s often the gate that gets used ten times for every one time the driveway gate opens. We install pedestrian gates with their own dedicated posts, a self-closing hinge if you want one, and optionally a keypad or intercom so it locks behind you. Because these gates are lighter, the hardware selection changes entirely, and we spec hinges rated for the gate’s actual weight rather than whatever came in the box.

Sliding Gate

A sliding gate travels horizontally along a track or rides on a cantilever system, which makes it the right choice for Dallas driveways that slope upward from the street or where a swinging gate would hit a car parked in the wrong spot. We install both tracked and cantilever sliding gates, and the critical work is in the rail alignment, the wheel tension, and the safety edges wired along the leading edge so the gate stops if it meets resistance. A sliding gate that’s a quarter-inch out of level will chew through wheels and pull the chain out of tension, so we level the rail with a laser and document the reading before we call the job done.

Swing Gate

A swing gate pivots on hinges mounted to posts and is the most common style for single-family driveways in Dallas, and it’s often a pair of leaves rather than one. We install single and double swing gates with hydraulic or electromechanical operators, and the thing that separates a good swing-gate installation from a bad one is what you can’t see: the steel core drilled into the post, the reinforcing plate behind the hinge, and the operator arm geometry that determines how the gate moves through its travel. We photograph the hinge mounting and the operator bracket before and after, so you can see exactly what was done.

Double Gate

A double gate is two gate leaves that meet in the middle, and in Dallas they’re common on wider driveways where a single leaf would be too heavy or would swing too far into the yard. The installation involves synchronizing two operators, which means both leaves need to move at the same speed, close in the right order, and stop without slamming. We set the limit switches on each leaf independently, then run the pair through a full open-close cycle while watching the overlap. If one leaf lags, we adjust the delay before we leave, not after you notice it.

Security Gate

A security gate is built with a different intent than a driveway gate: it’s designed to stop a vehicle, not just deter one. In Dallas, we install security gates for homeowners who want a heavier frame, a taller panel, and a locking mechanism that can’t be lifted off its track or popped with a screwdriver. These gates use heavier posts, deeper footings, and locks with a deadbolt throw instead of a latch, and we size the operator to the gate’s actual weight rather than its brochure weight. The result is a gate that clears your driveway and actually holds if someone tries to force it.

Brands We Service for Gate Installation

We install and service motors and operators from nine major gate-automation brands, so we’re not going to steer you toward replacing a perfectly good opener just because we don’t know how to work on it. That habit comes directly from Adrian Vance’s commercial access-control background, where the job was to keep existing hardware running, not to sell new hardware every time a capacitor failed.

On the installation side, we regularly mount and wire FAAC hydraulic operators for swing gates, BFT electromechanical arms and sliding operators, Linear commercial-grade operators for heavier residential gates, and Viking operators where the customer wants a specific feature set or has existing Viking hardware on the property. If you’ve got a LiftMaster on one side of the driveway and a Ghost Controls on the other, we’ll wire both. We’d rather work on what’s already there than sell you something new that you didn’t ask for.

Before

After

Signs You Need Gate Installation Right Now

• The gate post is leaning or the concrete footing is cracking. A leaning post is a structural failure, not a cosmetic one. In Dallas clay soil, posts set without deep enough footings shift with the seasonal moisture cycle, and once the post moves, the gate’s geometry goes with it. If you can push the post and see daylight at the base of the concrete, that gate is going to bind, sag, and eventually drop its hinges.
• The gate is rusted through at the bottom rail. Dallas humidity and the occasional ice storm are hard on steel gates, and rust almost always starts at the bottom rail where water pools and sits. If you can see through the metal, the gate’s structural integrity is gone, and welding patches onto a rotted frame just moves the failure point a foot further up. That’s the time to install new rather than repair old.
• The gate doesn’t match your access control needs anymore. If you’re adding a keypad, an intercom, or a phone-based entry system to a gate that was built before those existed, you may be looking at a retrofit that costs more than a clean installation. A new gate gives us the chance to run the conduit, mount the keypad post, and wire the photo-eyes in the right places from the start, instead of threading wires through a gate that was never designed for them.
• You’re replacing the fence and the gate is an afterthought. Most Dallas fence contractors will hang a gate, but they’re not gate operators, and the result is a gate that’s under-hung, under-hinged, and set on posts that were never sized for the weight. If you’re already tearing out the fence line, install the gate at the same time with a contractor who actually handles gate automation rather than treating the gate as a fence panel with hinges.
• You’ve had the same repair done twice in a year. If you’ve already paid someone to fix the same gate problem twice, that gate is telling you something: the hardware is expired. We see this in Dallas constantly, a gate motor that’s been patched and re-patched until the limit switch is worn out, the arm bracket is wallowed out, and the circuit board is on its third capacitor. A new installation with a written warranty is often the cheaper move than a third repair invoice.

Our Gate Installation Process - Step by Step

1. 1
   Site visit and measurement. We come to your Dallas property, measure the driveway width, check the slope, look at where the power is, and talk through what you actually want the gate to do. That means gate material, style, operator type, and access control. The written price comes out of this visit, and you get it before we do anything else.
2. 2
   Written scope and fixed price. You get a document that lists the gate, the operator, the posts, the footings, the conduit, the wire run, and the labor. The number on that document is the number you pay. No allowances, no “we’ll see how it goes,” no surprise line items at the end. This is Haven Standard Clause 1: have it in writing.
3. 3
   Footings and posts. We dig and pour the post footings to a depth that handles the gate’s weight and the operator’s torque, and we photograph the hole before the concrete goes in so you can see the depth. In Dallas clay, that depth matters. A post set at 24 inches will move. A post set at 42 inches with a properly sized concrete collar will hold.
4. 4
   Gate fabrication or delivery, mounting, and operator installation. The gate goes on, the hinges are set, the operator is mounted, and the wiring is run. We set the limits, the force settings, the closing speed, and the photo-eye alignment, and we photograph every setting as a reference for future service. If anything ever drifts, the next technician can see exactly where it was set.
5. 5
   Walkthrough and documentation. Before we leave, we run the gate through a full cycle with you standing there, show you the photo eye working, show you the keypad or intercom, and hand you the photo log and the written record of what was installed. That’s Clause 4: evidence on every job. You keep it, we file it, and if you call us in eight months with a question, we can pull the file and answer from the record instead of guessing.

How Much Does Gate Installation Cost in Dallas?

Gate Installation Near Dallas - Our Service Area

We install gates throughout Dallas and the surrounding metro, including gate installation in University Park, gate installation in Oak Cliff, Irving, Carrollton, Grand Prairie, Coppell, Plano, Murphy, Euless, Grapevine, and Rockwall. A live person answers the phone at (469) 299-5902 no matter where you’re calling from, and we’ll schedule your site visit at a time that works for you. If you’re not sure whether we cover your area, call and ask. If we can’t get there, we’ll tell you plainly rather than stringing you along.

Frequently Asked Questions - Gate Installation in Dallas

Schedule Your Gate Installation Service in Dallas Today

If you’re ready for a new gate, call (469) 299-5902 and we’ll set up a free site visit, hand you a written price, and walk you through exactly what’s going in and what it costs. No pressure, no vague estimates, just a fixed number on paper and a team that documents its work. We’re at home in Dallas, and we’ll answer the phone whenever you call.

Written by Adrian Vance, Owner at Vance Gate Repair Dallas, serving Dallas and the surrounding metro since 2014.