Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Arlington, TX
Gate access control in Arlington means keypads, card readers, and phone-entry systems on homes that sit on Blackland Prairie clay, where posts shift and wiring gets pulled loose. The work we do most often is replacing failed control boards, re-terminating corroded low-voltage wire, and re-aligning strike plates on gates that no longer swing the way they did last season. Call (469) 299-5902 and we’ll write the price down before anyone touches a tool.
Why Arlington Homes Are Different
Arlington’s residential streets, particularly east of Collins and through South Arlington, hold thousands of 1980s and 1990s tract homes with original wood gates now 30 to 40 years old. Those gates were framed on the assumption that the ground would stay put. It doesn’t. The expansive clay under Arlington swells after a wet spring and shrinks through a 100-degree August, so a gate post that sat true in June can lean two inches by Thanksgiving. That throws latch alignment, hinge geometry, and the operator’s travel limits all out of square at once.
North Arlington’s newer master-planned communities have their own pattern: ornamental iron and automated driveway gates governed by HOA design rules and built to look clean, but frequently wired with undersized operators relative to the gate’s weight. When the February freeze cycles hit, the same low-voltage control wiring that hums along fine at 95 degrees gets brittle and intermittent at 15. We see it every winter.
Our Main Arlington Services
Two services account for most of what Arlington homeowners call us about: access-control repairs on automated gates, and the mechanical parts and welding that keep the gate itself standing and swinging. Below are the three Arlington service pages for the jobs we handle most.
Gate Repair in Arlington
Broken hinges, sagging frames, stripped rack, misaligned sensors, dead operator, gate dragging the concrete. Repair starts with a written diagnosis and price. Gate Repair in Arlington
Gate Installation in Arlington
New gates on new posts, sized for Arlington clay and the actual wind load of your street. Includes written scope, HOA-compatible hardware when needed, and a photo log at the end. Gate Installation in Arlington
Gate Motor & Opener in Arlington
Operator replacement, arm retrofit, and control-board work on whatever brand is already mounted. We match the duty cycle to the gate’s weight, not the other way around. Gate Motor & Opener in Arlington
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Arlington
Gate access control in Arlington means keypads, card readers, and phone-entry systems on homes that sit on Blackland Prairie clay, where posts shift and wiring gets pulled loose. The most common failure we document is a corroded splice or a worn keypad membrane on a gate that the builder’s low-voltage installer ran through an unsealed conduit joint in 1995. That is not a guess; it is what the photo record shows. Since 2014, Adrian Vance has written the price down before the first wire is touched, and before we leave you get a photo log of every termination and a written record of which part was installed. That’s the same discipline we apply to commercial access-control work, now on residential Arlington gates. You can read the full scope of that work on our Gate Access Control page.
Keypad Entry
Signs you need it
You key the code and nothing releases, or the keypad accepts the code only some of the time, or the finish is cracked and water has been getting in.
What it costs in Arlington
A keypad replacement or new standalone install in Arlington typically runs $260-$620 depending on whether the wire from the house to the gate is still usable.
How we do it
We check for low-voltage shorts, re-terminate the wire at both ends, set and verify the code, then photograph every change before we leave.
Remote Control
Signs you need it
The remote only opens the gate from six inches away, or it only works when the engine is not running, or one remote works and the other does not.
What it costs in Arlington
Adding or replacing remotes in Arlington falls between $120 and $280 per remote including programming, unless we have to change out a failed receiver board.
How we do it
We identify the receiver’s dip-switch or encrypted code path, program the remote with the gate in learn mode, and note the frequency and coding method on the job record.
Phone Entry
Signs you need it
You or your delivery driver dials the gate and hears dead air, or the system rings through on a landline that no longer exists.
What it costs in Arlington
Phone-entry repairs and new installs for Arlington gates typically run $350-$900 depending on whether we are wiring to an existing phone line or switching to cellular.
How we do it
We test line voltage, confirm the relay that trips the gate operator, and set or update the forwarding number before documenting the call log and the relay output.
What Gate Access Control Costs in Arlington
| Item | Typical range in Arlington |
|---|---|
| Keypad replacement or install | $260-$620 |
| Remote add or replace | $120-$280 |
| Phone entry repair or cellular upgrade | $350-$900 |
Does an Arlington access-control system survive the summer heat?
Yes, but only if the enclosure is sealed and the wire is not already brittle from prior heat cycles. Most failures we photograph in August are not the processor; they are the cracked seals and loose conduits that let humidity in during spring.
Can you use my existing keypad and wiring?
Most of the time, yes. We test the wire first, because on older Arlington homes the burial depth is shallow and root damage near the fence line is common. If the wire tests good, we reuse it and quote only the components.
Gate Parts & Welding in Arlington
Gate parts and welding in Arlington are dominated by the old wood gates on 1980s and 1990s lots, where hinges have wallowed out their screw holes and posts have heaved on clay. We weld, re-set, and re-align these gates every week of the year, and the reason is almost always the same: the Blackland Prairie soil under the post is moving, and the hardware is taking the strain. That is the problem our Gate Parts & Welding work solves at the mechanical level, before any operator or keypad is discussed.
Hinge Replacement
Signs you need it
The gate scrapes the ground at the latch side, or you can lift the gate half an inch and feel the play, or there are rust streaks running down from the hinge pin.
What it costs in Arlington
Hinge replacement or rebuild work in Arlington generally runs $140-$380 per gate depending on how far the original screw pattern has been destroyed.
How we do it
We cut the old fasteners, weld or epoxy new anchors as the material allows, set the gate on the new pins, and photograph the restored swing line.
Post Replacement
Signs you need it
The post is visibly leaning, the gate has started binding at the top corner, or the post wiggles when you push it with one hand.
What it costs in Arlington
Post replacement in Arlington’s clay runs $300-$800 per post depending on the dig, the concrete volume, and whether we cut and re-weld the hinge blocks.
How we do it
We set the new post with a deeper footing than the original, brace it true, backfill over compacted stone, and record the plumb reading before we remount the gate.
Custom Welding
Signs you need it
The frame has cracked at a corner, a hinge tab has torn out of the stile, or you want a bracket added that the gate was never designed for.
What it costs in Arlington
Custom welding or crack repair on Arlington gates and frames generally runs $180-$650 depending on the prep work and the number of passers needed.
How we do it
We grind the crack to clean metal, weld with the right filler for the base steel, then repaint or treat the repair and photograph the bead before it cools.
What Gate Parts & Welding Costs in Arlington
| Item | Typical range in Arlington |
|---|---|
| Hinge replacement or rebuild | $140-$380 |
| Post replacement (clay soil dig) | $300-$800 |
| Custom welding or crack repair | $180-$650 |
Is it cheaper to weld my old gate than to replace it?
Often yes, if the frame is still sound. We tell you in writing which way the numbers go. A straight crack with clean metal is welder territory; a rusted-through frame is money better spent on new steel.
Can you reset my gate post without killing the grass?
We can dig a clean footing at the post base with minimal disturbance, but in Arlington clay the answer is not to reset the same depth; it’s to go deeper and add stone so the next wet season does not shove it again.
Brands We Service in Arlington
We service and stock parts for our brands including FAAC, BFT, Linear, Viking, LiftMaster, DoorKing, Ghost Controls, Mighty Mule, and Elite. We repair whatever is already mounted rather than steering you toward a replacement. Most common Arlington parts are on the truck or one day out.
Pricing for Gate Repair in Arlington, TX
| Service | Typical range in Arlington |
|---|---|
| Keypad entry replacement or install | $260-$620 |
| Remote control add or reprogram | $120-$280 |
| Phone entry repair or upgrade | $350-$900 |
| Hinge replacement or rebuild | $140-$380 |
| Post replacement in clay soil | $300-$800 |
| Custom welding or crack repair | $180-$650 |
Two things push prices up in Arlington: the clay, which adds dig and footing depth on any post job, and the age of the original low-voltage wire on access-control work, which sometimes forces a new run instead of a re-termination. The price we hand you is the price you pay; it is written down before work starts, and it does not change at the end of the job.
Neighborhoods We Serve in Arlington
We run access-control and parts-and-welding calls across the city, including these neighborhoods:
- Dalworthington Gardens
- Pantego
- Southwest Arlington
- Interlochen
- North Arlington
Most service calls are scheduled the same week; emergency gate-down calls are answered by a live person 24 hours a day at (469) 299-5902, and a technician is dispatched from the metro office to Arlington without a callback queue.
Service Area - Cities Near Arlington
Vance Gate Repair services Arlington and the surrounding cities of Grand Prairie, TX, Bedford, TX, Euless, TX, and Grapevine, TX. The same written-price standard applies in every city, and every job across the metro is scheduled through the same live phone line.
Serving Arlington, TX - Our Local Coverage Area
We’re based in the Arlington area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Arlington
If your gate is visible from the street and your HOA has an architectural review clause, most Arlington HOAs require written approval before a post or gate is replaced, and sometimes before a new operator is mounted. We can supply the written scope and material list your board asks for. Bring the HOA requirements to the free estimate and we will quote to those specs.
Same day in almost all cases; our live line is answered around the clock and an Arlington technician is dispatched directly, not through a call queue. If the job cannot be finished the same day, we will leave the gate secure and the written repair scope in your hand.
Yes. The written price is the contract. If we find a second problem while working, we stop and show it to you with a new written line before touching it. You approve the final number with a signature, not a handshake.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Arlington Customers Say
"Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H."They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C.