Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Bedford, TX
Gate access control in Bedford usually means one of two things: a keypad or intercom that stopped talking to an opener built before smartphones existed, or a gate that won’t stay latched because the post has moved. Most Bedford homes went up between the mid-1970s and early 1990s, and the original cedar privacy gates are now 30 to 50 years old. That age, combined with North Texas clay soil that heaves seasonally, creates failures no brand-new motor can fix by itself. Call (469) 299-5902 and we’ll tell you what’s actually wrong before you spend a dollar.
Why Bedford Homes Are Different
Bedford is fully built out. The residential streets north of Highway 183 and south of Harwood Road are overwhelmingly single-family tract homes from the 1970s through early 1990s, which means the original cedar board-on-board fence gates across the city are aging out at the same time. We see entire blocks where three or four gates fail in the same season, not because of bad luck but because they were all built with the same materials and the same post-setting methods.
The bigger factor is the soil. Bedford sits on Blackland Prairie clay, which swells when spring storms soak it and contracts hard in 100°F summer heat. A gate that closes clean in March can drag or refuse to latch by August with no hardware failure at all, because the post itself has tilted out of plumb. High-wind severe thunderstorms also sweep through the mid-cities corridor regularly, popping old hinges and blowing gates off latches. One pattern we see often in Bedford: the north and west fence lines, facing the prevailing storm direction, show accelerated hinge-side rot and lean while the south-side gate in the same yard is structurally fine.
Our Main Bedford Services
Most Bedford homeowners call us for one of three things: a gate that won’t open, a gate that needs replacing, or a motor that quit. Here’s what each involves locally.
Gate Repair in Bedford
Bedford gate repair usually comes down to hinges, posts, or the latch assembly on cedar swing gates that predate modern footing standards. We reset leaning posts, replace rusted hinges, weld cracked frames, and realign drooping gates. The clay soil means repairs here often need post adjustment, not just new hardware. Gate Repair in Bedford covers the full scope.
Gate Installation in Bedford
New gate installation in Bedford means working around existing fence lines and mature trees, plus post footings sized for clay soil movement. We build steel, aluminum, and wood gates to match the fence style, set posts below the frost line with proper concrete, and hang the gate with hardware rated for the weight. For a written quote on a new gate, see Gate Installation in Bedford.
Gate Motor & Opener in Bedford
Bedford’s aging swing gates often have motors from brands like Linear, FAAC, or Mighty Mule that are still serviceable but need limit switch adjustment, new capacitors, or replacement control boards. We repair before recommending replacement, and we work on nine automation brands. Gate Motor & Opener in Bedford details motor repair and replacement.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Bedford
Bedford’s housing stock creates a specific access control problem: homeowners want keypad or phone entry added to a 1980s-era swing gate, but the gate post has shifted and the opener is a brand most installers won’t touch. That combination means the access system has to be installed around existing conditions, not on a clean new build. We handle the full access control job, from running wire to programming credentials, and every visit ends with a written record of what was installed and how it was set. This is the work detailed on our Gate Access Control hub.
Keypad Entry
Signs you need it
The gate only opens with a remote, and anyone without that exact remote can’t get in or out.
What it costs in Bedford
Keypad entry in Bedford typically runs $450-$950 including wiring and programming.
How we do it
We mount the keypad, run low-voltage wire to the opener, program entry codes, and photograph the wiring before we leave.
Video Intercom
Signs you need it
You can’t see or talk to whoever is at the gate before deciding whether to open it.
What it costs in Bedford
Video intercom systems in Bedford typically run $1,300-$2,900 depending on monitor count and gate distance from the house.
How we do it
We install the gate station, run communication cable, mount the indoor monitor, and test audio and video with you standing at the gate.
What Gate Access Control Costs in Bedford
| Item | Typical range in Bedford |
|---|---|
| Keypad entry | $450-$950 |
| Phone entry system | $800-$1,600 |
| Video intercom | $1,300-$2,900 |
Can you add a keypad to an existing Bedford gate opener?
Usually, yes. Most openers from Linear, FAAC, BFT, and Mighty Mule accept a wired keypad. If your opener predates external inputs, we can add a receiver module. Call (469) 299-5902 and we’ll confirm compatibility over the phone.
Does access control work when the power is out in Bedford?
Not on its own. Most systems lose power with the house unless there’s a battery backup. We can add a backup battery to keypad and intercom systems so the gate still opens during spring storm outages.
Gate Parts & Welding in Bedford
Bedford’s 30-to-50-year-old cedar gates fail at the steel parts first: hinges rust through, drop rods bend, and the corner brackets holding the wood frame together crack. Many of these gates were built before welded steel frames were standard, so the repair often means adding steel where there was only wood. Our Gate Parts & Welding service covers everything from hinge swaps to full post replacement.
Hinge Replacement
Signs you need it
The gate sags toward the latch side and scrapes the ground even after adjusting the post.
What it costs in Bedford
Hinge replacement in Bedford typically runs $120-$260 per hinge, with most swing gates needing two or three.
How we do it
We unweight the gate, remove the old hinges, weld or bolt new ones rated for the gate’s actual weight, and photograph the finished install.
Post Replacement
Signs you need it
The post leans visibly, the gate won’t latch, or the wood is soft and rotting at ground level.
What it costs in Bedford
Post replacement in Bedford typically runs $450-$950 per post including new concrete set below the clay line.
How we do it
We cut the old post out, auger a new footing, set a steel or treated post in concrete, and rehang the gate plumb.
What Gate Parts & Welding Costs in Bedford
| Item | Typical range in Bedford |
|---|---|
| Hinge replacement | $120-$260 per hinge |
| Post replacement | $450-$950 per post |
| Custom steel frame welding | $380-$1,100 |
Can you weld a broken gate frame without taking the gate down in Bedford?
Sometimes. If the crack is accessible and the gate is stable, we can weld in place. If the frame is rusted through in multiple spots, removing the gate to weld on the ground produces a stronger repair. The written quote tells you which one applies.
How long does a welded steel frame last on a Bedford cedar gate?
Fifteen to twenty-five years if the steel is primed and painted and the post footing is solid. The wood pickets may need replacement sooner, but the frame holds.
Brands We Service in Bedford
We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We stock common control boards, remotes, and photo-eyes for most of these brands, which keeps turnaround short in Bedford. See our brands for the full list.
Pricing for Gate Repair in Bedford, TX
| Service | Typical range in Bedford |
|---|---|
| Gate motor replacement | $680-$1,900 |
| Gate opener repair | $180-$620 |
| Swing gate installation | $1,400-$4,200 |
| Keypad entry | $450-$950 |
| Phone entry system | $800-$1,600 |
| Video intercom | $1,300-$2,900 |
| Hinge replacement | $120-$260 per hinge |
| Post replacement | $450-$950 per post |
| Custom steel frame welding | $380-$1,100 |
| Gate roller replacement | $160-$340 |
Two things push Bedford prices higher than the regional average: clay soil movement that requires deeper post footings, and the age of the original cedar gates, which often means the first quote uncovers a second problem once we start. Under the Haven Standard, the price is written and handed to you before any work starts, so the number on the quote is the number on the invoice.
Neighborhoods We Serve in Bedford
We work across Bedford’s single-family neighborhoods, from the older streets off Forest Ridge Drive to the homes along Harwood Road and Cheek-Sparger Road. Most Bedford calls get a same-day or next-day visit depending on the work.
- Shady Brook
- Brookside
- Woodland Hills
- Stonegate
- Meadow Creek
Service Area - Cities Near Bedford
Beyond Bedford, we cover the surrounding mid-cities suburbs. We handle gate work in Euless, TX, Grapevine, TX, Grand Prairie, TX, and Coppell, TX with the same written-price policy on every job.
Serving Bedford, TX - Our Local Coverage Area
We’re based in the Bedford area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Bedford
Most Bedford repair calls get a same-day or next-day visit. Emergency calls, like a gate stuck open or a car trapped inside, are prioritized. A live person answers (469) 299-5902 at any hour, not a voicemail queue.
For most like-for-like gate repairs and replacements, no permit is required. If the work involves new electrical runs or a new opener, Bedford may require an electrical permit. We confirm permit status in writing before starting.
We can give a firm range for most common repairs based on photos or a description. The exact written price comes after we see the gate in person. Under our policy, that written price is in your hand before any work begins.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Bedford Customers Say
"They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."Quoted in writing, installed on the day promised, and the price did not move. The crew was licensed and the number was on the paperwork."
- Wes A."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N.